|
Post by cdbias on Jul 29, 2013 21:52:31 GMT -5
Is anyone going out tomorrow?
|
|
|
Practice
Jul 29, 2013 22:48:12 GMT -5
via mobile
Post by davidholdren on Jul 29, 2013 22:48:12 GMT -5
Me and zach will be their bout 630 with our 2wd rich will be their about 600 with his 4wd..
|
|
|
Post by cdbias on Jul 29, 2013 22:53:17 GMT -5
I may come and work a little. Play a little. It would be around 6
|
|
|
Post by Thunder on Jul 30, 2013 8:46:14 GMT -5
If I can get my esc problem taken care of I will be out, reinstalled my newer Novak but having problems with it on again off again, you have to nudge it and it will run, not using the same motor I had troubles with, changed..
|
|
|
Post by cdbias on Jul 30, 2013 9:06:20 GMT -5
Have you contacted Novak? You seem to be having a lot of issues with them.
|
|
|
Post by baustin on Jul 30, 2013 9:21:03 GMT -5
|
|
|
Practice
Jul 30, 2013 9:29:15 GMT -5
via mobile
Post by speedy1234 on Jul 30, 2013 9:29:15 GMT -5
Have you tried changing the sensor cable?
Patrick
|
|
|
Post by baustin on Jul 30, 2013 9:41:21 GMT -5
On a more serious note DC is now running Novak.....he said their customer service is awesome.....or maybe he will chime in, if he knows to look here......
|
|
|
Practice
Jul 30, 2013 9:42:43 GMT -5
via mobile
Post by trey on Jul 30, 2013 9:42:43 GMT -5
|
|
|
Practice
Jul 30, 2013 9:43:51 GMT -5
via mobile
Post by trey on Jul 30, 2013 9:43:51 GMT -5
I was hoping someone was going! See you there!
|
|
|
Post by baustin on Jul 30, 2013 9:51:03 GMT -5
www.rctech.net/forum/rookie-zone/449487-motor-needs-push-start.html"I had that symptom and it was blown MOSFETs on the ESC." "I had a Novak with the same problem and it was also a blown mosfet in the ESC. I have also seen sensor issues cause similar problems. Try the Mamba in different modes including Smart-Sense and sensored only to see if you can eliminate a sensor problem. In Smart-Sense it should start the motor with or without sensors connected." "Quote: Originally Posted by burnineyes View Post I had a Novak with the same problem and it was also a blown mosfet in the ESC. same here."
|
|
|
Post by baustin on Jul 30, 2013 9:59:04 GMT -5
lol......"we talkin' bout practice, not a game but practice!!!!".......listen to, radio impound podcast........they will fill u in.....infamous interview from Allen Iverson where the media is hassling him about being late and not giving a full effort at practice......
|
|
|
Practice
Jul 30, 2013 10:06:32 GMT -5
via mobile
Post by speedy1234 on Jul 30, 2013 10:06:32 GMT -5
If u remeber correctly thunder is running a mamba max pro with the novak motor.
|
|
|
Post by baustin on Jul 30, 2013 10:10:51 GMT -5
Ah I thought it was a GTB.....the guy who started that thread on rc-teck was for a mamba max pro.....
"I have a tekin brushless with a mamba max pro esc. When I start it runs until I come to a complete stop, then usually wont move unless it gets a slight push. Then it does the same thing. This is new equipment and started on my second time out. I reset the esc, checked my mesh, slipper and diff and its still the same thing. Any ideas?"
"Does sound like a sensor issue somewhere. Can you get a hold of another motor to try?
Could be the sensor board in the motor, something on the sensor, or poor alignment of same relative to the rotor.
Seems you've covered the sensor cable, double check the connections at each end. I had a small spec of dirt in the socket give me fits for a while once.
Worst case, a problem with the internal esc sensor circuitry.
Unless it's because the timing is jacked up too much? Not sure, but think I've heard of that being an issue."
|
|
|
Practice
Jul 30, 2013 10:14:02 GMT -5
via mobile
Post by speedy1234 on Jul 30, 2013 10:14:02 GMT -5
Lol i meant if i remember....
|
|